Appearance
Diode Bridge Rectifier (3-phase)
Uncontrolled three-phase 6-pulse bridge rectifier (Graetz). Six diodes (three in the positive group, three in the negative group) fed from a single electrical_3ph AC bus, rectifying to dc_pos / dc_neg. All internal diodes share the same forward-voltage drop and on/off resistances. Each internal diode keeps its own piecewise-linear state and registers an in-solve switch evaluator with the Cholesky solver, so the bridge converges within one outer step even when multiple diodes flip simultaneously (stiff zero-crossing handling, needed for inductive DC loads where the freewheel hand-off across diodes must happen instantaneously). Two independent current-monitoring toggles emit the aggregate DC output current, the per-diode currents, or both.
Category: Power Electronics / Rectifiers
Ports
| Port | Kind | Signal | Notes |
|---|---|---|---|
ac | Three-phase terminal | — | |
dc_pos | Electrical terminal | — | |
dc_neg | Electrical terminal | — |
Parameters
Config
| Parameter | Type | Default | Units | Description | ID |
|---|---|---|---|---|---|
| Vf | Number | 0.7 | — | Per-diode forward conduction threshold (V). Applied to every internal diode in the bridge. | v_forward |
| R_on | Number | 0.05 | Ω (also kΩ, MΩ) | Per-diode conducting (forward-biased) resistance. Pick a unit from the dropdown. Applied to every internal diode. | resistance_on |
| R_off | Number | 1000000 | Ω (also kΩ, MΩ) | Per-diode blocking (reverse-biased) resistance. Pick a unit from the dropdown. Applied to every internal diode. | resistance_off |
| Measure bridge (DC) current | Choice: Off / On | Off | — | Emit the aggregate DC output current as a single observable (sum of currents through the upper-group diodes; by KCL at the DC+ rail this equals the current flowing OUT of dc_pos into the external load). | measure_bridge_current |
| DC positive direction | Choice: +ve in / +ve out | +ve out | — | Sign convention for this current. '+ve out' (default) is positive when current flows out of dc_pos into the external load. '+ve in' flips the sign. | dc_current_dir |
| Measure per-diode currents | Choice: Off / On | Off | — | Emit one observable per internal diode (6). Each diode current is signed anode→cathode. Independent of Measure bridge (DC) current — enable both at once when you need both views. | measure_diode_currents |
| Diode positive direction | Choice: +ve in / +ve out | +ve in | — | Sign convention for this current. '+ve in' (default) is positive when current flows into each diode at its anode, toward the cathode. '+ve out' flips the sign. | device_current_dir |
Bridge Current
| Parameter | Type | Default | Units | Description | ID |
|---|---|---|---|---|---|
| DC current name | Text | I_dc | — | Signal name for the aggregate DC output current (A). Blank = skip emission. | bridge_current_name |
Per-Diode Currents
| Parameter | Type | Default | Units | Description | ID |
|---|---|---|---|---|---|
| D1 current name | Text | I_d1 | — | Signal name for diode D1 branch current (A). Positive-group A-phase diode (ac_a → dc_pos). Blank = skip emission. | current_name_d1 |
| D2 current name | Text | I_d2 | — | Signal name for diode D2 branch current (A). Positive-group B-phase diode (ac_b → dc_pos). Blank = skip emission. | current_name_d2 |
| D3 current name | Text | I_d3 | — | Signal name for diode D3 branch current (A). Positive-group C-phase diode (ac_c → dc_pos). Blank = skip emission. | current_name_d3 |
| D4 current name | Text | I_d4 | — | Signal name for diode D4 branch current (A). Negative-group A-phase diode (dc_neg → ac_a). Blank = skip emission. | current_name_d4 |
| D5 current name (3-phase only) | Text | (empty) | — | Signal name for diode D5 branch current (A). Negative-group B-phase diode (dc_neg → ac_b). Blank = skip emission. | current_name_d5 |
| D6 current name (3-phase only) | Text | (empty) | — | Signal name for diode D6 branch current (A). Negative-group C-phase diode (dc_neg → ac_c). Blank = skip emission. | current_name_d6 |
Observables
| Default name | Kind | Recorded when | Description | ID |
|---|---|---|---|---|
| set by DC current name | Signal | Measure bridge (DC) current is on | Aggregate DC output current (A). Sum of currents through the positive-group diodes (D1+D2+D3); by KCL at the DC+ rail this equals the current flowing OUT of dc_pos into the external load. Positive out of dc_pos into the external load for '+ve out' (default); the other direction flips the sign. | dcCurrent |
| set by D1 current name | Signal | Measure per-diode currents is on | D1 branch current (A, anode → cathode). Positive-group A (ac_a → dc_pos). The direction switch keeps this sign by default and flips it the other way. | branchCurrent_0 |
| set by D2 current name | Signal | Measure per-diode currents is on | D2 branch current (A). Positive-group B (ac_b → dc_pos). The direction switch keeps this sign by default and flips it the other way. | branchCurrent_1 |
| set by D3 current name | Signal | Measure per-diode currents is on | D3 branch current (A). Positive-group C (ac_c → dc_pos). The direction switch keeps this sign by default and flips it the other way. | branchCurrent_2 |
| set by D4 current name | Signal | Measure per-diode currents is on | D4 branch current (A). Negative-group A (dc_neg → ac_a). Positive into each diode at its anode, toward the cathode for '+ve in' (default); the other direction flips the sign. | branchCurrent_3 |
| set by D5 current name (3-phase only) | Signal | Measure per-diode currents is on | D5 branch current (A). Negative-group B (dc_neg → ac_b). Positive into each diode at its anode, toward the cathode for '+ve in' (default); the other direction flips the sign. | branchCurrent_4 |
| set by D6 current name (3-phase only) | Signal | Measure per-diode currents is on | D6 branch current (A). Negative-group C (dc_neg → ac_c). Positive into each diode at its anode, toward the cathode for '+ve in' (default); the other direction flips the sign. | branchCurrent_5 |